Your Ford Ranger Raptor turns heads everywhere it goes — but is the rear end finishing the look the way it should? Bare trunk side panels leave your truck feeling unfinished, especially compared to the aggressive front grille and bold fender flares that define the Raptor. If you've ever stared at the back of your truck and felt something was missing, this is the fix. Our Rear Trunk Side Letter Decal delivers a factory-quality graphic that completes your Raptor's aggressive identity in minutes.
Order Now →
What Is the Rear Trunk Side Letter Decal for Ford Ranger Raptor?
This is a precision-cut vinyl film letter decal designed specifically for the rear trunk side panels (bed sides) of the Ford Ranger Raptor. Each panel measures approximately 47.2 inches long by 4.7 inches wide, contoured to follow the natural body lines of the Raptor's bed and provide bold, legible text graphics with a clean, OEM-inspired finish.
Unlike generic stick-on letters or universal kits that leave gaps and uneven spacing, this decal is shaped to match the Raptor's specific panel geometry. The PVC vinyl construction is UV-resistant, weather-tough, and built to hold its color through years of sun, rain, car washes, and trail dust.
Think of it as the missing piece — the same kind of branded body graphic you'd expect to see roll off a factory floor, but priced as an everyday upgrade rather than a dealership accessory.
Key Benefits
- Vehicle-specific fitment: Designed for the Ford Ranger Raptor (all model years) — no trimming, no guesswork, no awkward gaps.
- Premium UV-resistant PVC vinyl: Holds its black depth and sharp edges in direct sun, rain, snow, and frequent washing.
- Factory-look finish: Clean letterform, smooth lay-down, and a low-profile thickness that reads as OEM rather than aftermarket.
- Generous panel size: At ~47.2 in. long, each decal commands attention without overpowering the bed lines.
- Easy DIY install: Peel, position, squeegee — most owners complete both sides in under an hour with basic prep.
- Affordable styling upgrade: At $23.99, it's one of the highest-impact, lowest-cost mods you can do to a Raptor.
Why Your Ford Ranger Raptor Deserves This Upgrade
The Ranger Raptor is built to be noticed — wide stance, performance suspension, and a presence that doesn't apologize. But the factory bed sides leave a lot of blank real estate. Without graphics, your Raptor blends in with regular Rangers from the rear three-quarter angle. Bold side-panel lettering reclaims that visual identity and pulls your truck back into "performance edition" territory where it belongs.
There's also a practical layer. Vinyl on the bed sides acts as a buffer against light surface scratches from brushing against gear, bikes, branches, or the occasional door ding from a parking lot. While this isn't a substitute for full paint protection film, it does add a thin protective barrier on a high-contact area. If you're serious about preserving your paint long-term, pair this with options from our PPF Kits collection, or explore more truck-specific graphics in our Vehicle Decals collection to build out a coordinated look.
What's Included & Installation
Each order includes two precision-cut vinyl film letter decals — one for the driver-side bed panel and one for the passenger-side panel — sized at approximately 47.2 in. L × 4.7 in. W per piece. Application tape comes pre-applied for accurate transfer and clean alignment.
Installation is straightforward:
- Wash and dry the bed-side panels thoroughly, then wipe with isopropyl alcohol to remove all wax and oils.
- Use masking tape to mock up the placement and stand back to confirm alignment before peeling.
- Slowly peel the backing, lay the decal down from one edge, and squeegee outward to eliminate air bubbles.
- Remove the transfer tape at a sharp angle once the vinyl has adhered evenly.
For owners who prefer a flawless first-try result, any local detail or wrap shop can install these in roughly 30–45 minutes — usually for a modest labor fee.
Frequently Asked Questions
Will this decal fit all Ford Ranger Raptor model years?
Yes. The decal is designed for the Ford Ranger Raptor across all model years. The shape and dimensions align with the standard Raptor bed-side panel geometry, so fitment is consistent regardless of build year.
How long will the vinyl last on my truck?
With proper installation and basic care, expect 5+ years of strong outdoor performance. The UV-resistant PVC vinyl is built to resist fading, cracking, and lifting through normal sun exposure, weather, and routine car washes. Avoid high-pressure washing directly at the edges to maximize lifespan.
Can I remove the decal later without damaging my paint?
Yes. Quality vinyl film like this removes cleanly when warmed gently with a heat gun or hair dryer. As long as your factory paint is in good condition and the decal hasn't been on for an unreasonably long time, no residue or damage should remain. Always pull at a low angle and work slowly.
Finish the Look Your Raptor Was Built For
The Ford Ranger Raptor is a statement truck — and the rear bed panels are prime real estate to make that statement louder. This vinyl film letter decal delivers a factory-grade graphic, vehicle-specific fitment, UV-resistant durability, and a confident finished look, all at a price that makes it a no-brainer upgrade. Skip the generic stickers and the overpriced dealership accessories. Get the right decal, built for your truck, ready to install today.
Looking for more Raptor styling? Check out our Hood Stripe Decal for Ford F-150 / Ranger Raptor to coordinate the front and rear. Driving a different rig? See our RAM 1500/2500 HEMI Rebel Decal or our Toyota Tundra TRD Splash Grunge Decal Kit. You can also browse the rest of our