Your Ford Ranger Raptor already turns heads — but does the rear of your truck look as aggressive as the front? Most Raptor owners pour attention into the grille and hood, only to leave the rear bed sides looking plain and unfinished. If you've been searching for that one upgrade that ties the whole build together without breaking the bank, you've just found it. These rear trunk side letter vinyl decals deliver bold, factory-style lettering that completes your truck's stance and gives it the presence it deserves.
Order Now →
What Is the Rear Trunk Side Letter Vinyl Decal for Ford Ranger Raptor?
This is a precision-cut PVC vinyl film decal kit designed specifically for the rear bed sides of the Ford Ranger Raptor. Each panel measures approximately 47.2 inches long by 4.7 inches wide and applies directly to the rear trunk/bed side area, replicating the bold lettered look found on premium factory and aftermarket builds.
Unlike cheap stickers that peel within months, this decal is made from automotive-grade vinyl film engineered to handle daily driving abuse — UV rays, rain, road grime, car washes, and temperature swings. The lettering sits flush against the body panel for a seamless OEM appearance that looks painted on rather than applied.
Because it's cut specifically for the Ranger Raptor's rear bed contour, you don't have to guess where it goes or trim anything to fit. The pre-cut design follows the body lines exactly, so installation is straightforward and the result is consistent on both sides.
Key Benefits
- Vehicle-specific fit: Engineered for the Ford Ranger Raptor's rear bed dimensions — no trimming, no guessing.
- Premium PVC vinyl film: UV-resistant, weatherproof, and built to hold its color and adhesion through years of daily use.
- Bold factory-style lettering: Mimics high-end OEM and aftermarket graphics for a finished, aggressive look.
- Two full panels included: Driver and passenger side, each approximately 47.2 in. L x 4.7 in. W.
- DIY-friendly install: Smooth application with basic tools — no shop visit required for confident installers.
- Paint protection bonus: Adds a layer of film over high-impact bed side areas, helping shield paint from minor scuffs and UV fade.
Why Your Ford Ranger Raptor Deserves This Protection
The Ranger Raptor is built for adventure — which means the rear bed sides take a constant beating. Loose gravel kicked up from the rear tires, tree branches brushing past on trail runs, loading and unloading gear, and relentless UV exposure all chip away at your factory paint over time. Once that clear coat is compromised, fading and oxidation aren't far behind, and that damage shows up first on flat, sun-facing panels like the bed sides.
A vinyl film decal isn't just cosmetic — it's a sacrificial layer that takes the abuse so your paint doesn't have to. Pair this kit with a full PPF kit for high-impact zones like the hood and fenders, and your Raptor stays showroom-fresh far longer. Want to see what else fits your truck? Check out our full vehicle decal collection for more Ranger Raptor styling options.
What's Included & Installation
Each order includes two pre-cut vinyl film decals — one for the driver side and one for the passenger side of the rear trunk/bed area. The decals arrive ready to apply with transfer tape backing.
Basic install steps:
- Thoroughly wash and dry the rear bed side panels.
- Wipe the application area with isopropyl alcohol to remove all wax and residue.
- Use the wet-install method (mix water + a few drops of dish soap in a spray bottle) for easier positioning.
- Align the decal carefully, then squeegee from the center outward to remove air bubbles.
- Let it cure for 24 hours before washing or exposing to high-pressure water.
Comfortable with vinyl? You can knock this out in under an hour in your driveway. If you'd rather have it done perfectly the first time, any local detail shop or wrap installer can apply it for a small fee.
Frequently Asked Questions
Will this fit every year of the Ford Ranger Raptor?
Yes — this decal kit is designed to fit all model years of the Ford Ranger Raptor. The rear bed side dimensions have remained consistent across generations, so you'll get a clean fit whether your truck is current or a few years old.
How long does the vinyl film last?
With proper installation and basic care, the PVC vinyl film typically holds up for 5+ years outdoors. It's UV-resistant and weatherproof, so it won't fade, crack, or peel under normal driving conditions. Avoid harsh chemical solvents and high-pressure washing directly on the edges to maximize lifespan.
Can I remove the decal later without damaging my paint?
Yes. Quality vinyl film like this is designed to remove cleanly when warmed gently with a heat gun or hair dryer. As long as your factory paint and clear coat are in good condition when the decal was applied, removal won't leave residue or damage the finish underneath.
Finish the Build Your Raptor Deserves
Your Ford Ranger Raptor was built to stand out — and a bare, plain rear bed side is the one detail holding it back. For just $23.99, this pre-cut vinyl film decal kit transforms the rear of your truck with bold, factory-style lettering that looks like it rolled off a custom build at twice the price. UV-resistant, weatherproof, and engineered specifically for your Raptor, it's the easiest high-impact upgrade you can make this weekend. Pair it with a hood stripe decal to complete the look, or browse our best sellers for more proven upgrades. Don't let your Raptor look unfinished one more day.
Related Upgrades
- Hood Stripe Style Decal for Ford F-150 / Ranger Raptor — Order Here
- Back Door & Side Decal for Dodge RAM 1500 / 2500 HEMI Rebel —